Whirlpool Washer F9 E1 Error Code: Slow Drain and How to Fix It
Also shown or searched as: F9E1, drn
On a Whirlpool washer, F9 E1 (F9E1, or drn on some top loaders) is the long drain code: the washer took too long to pump out the water. Whirlpool's first checks are how deep the drain hose sits, tape or kinks at the standpipe, and on front loaders the drain pump filter. If draining stays slow, have the pump checked.
What to try first
Safety: Unplug the washer before you open the filter panel. More water comes out than one pan holds, so keep towels on the floor and empty the pan as you go.
- 1
Measure how deep the hose goes
Pull the drain hose out of the standpipe or laundry tub and look at how much was inside. Whirlpool allows no more than 4.5 inches. The U-shaped hose form that came with the washer sets that length; on top loaders, Whirlpool says to leave the factory hose form exactly as it was shipped.
- 2
Remove any tape and leave an air gap
Seat the hose loose but secure, never taped over or sealed into the pipe. The open gap lets air in, which stops suction from dragging water back and forth through the hose.
- 3
Straighten the hose and clear the house drain
Pull the washer forward a few inches and look for bends or flattened spots behind it. If the standpipe or utility sink drains slowly on its own, clear that blockage before blaming the washer.
- 4
Check the hose height for your washer type
On Whirlpool front loaders the hose can rise up to 96 inches above the bottom of the washer. On top loaders, Whirlpool wants the end of the hose higher than 36 inches off the floor, or the washer can siphon. All-In-One washer dryers need the hose routed between 24 and 96 inches.
- 5
Clean the drain pump filter on a front loader
Unplug the washer. On models with a storage drawer, pull it open and free it with the tab on each side. Set a broad, flat pan under the filter, unclip the small black hose, pull its plug and let the water out, emptying the pan as often as needed. Plug the hose and clip it back. With a cloth underneath, turn the filter counterclockwise to remove it, pull off the lint, rinse it, and turn it back in clockwise as far as it goes, handle as close to upright as possible.
- 6
Clear the holes in the door seal
On a front loader, fold back the bottom of the rubber door seal and pick lint out of the small drain holes, following the seal cleaning steps in your owner's manual.
- 7
Reset and test
Leave the washer unplugged for 5 minutes, plug it back in and run a short rinse and spin. Watch whether the drum empties before the spin starts.
Most likely causes of F9 E1
1. A drain hose pushed too far into the standpipe, or taped in place (most common)
More than 4.5 inches of hose sits inside the pipe, or tape seals the gap around it. Either one lets drained water siphon back into the tub, so the pump keeps moving the same water.
2. A clogged drain pump filter on a front loader (most common)
Lint, hair or a small item is caught on the filter behind the bottom drawer or lower panel. Whirlpool's Laundry Tower page names a blocked drain pump as the likely cause of F9E1.
3. A kinked drain hose, or a slow standpipe or utility sink (common)
The hose is folded where the washer was pushed back against the wall, or the standpipe or sink backs up while the washer pumps out.
4. Clogged drain holes in the rubber door seal (less common)
Front loaders only. Water stays in the fold at the bottom of the door seal after a cycle, or lint is packed into the small holes there.
5. A worn or failed drain pump (less common)
The hose, the filter and the house drain all check out, yet the code comes back after a 5-minute power reset.
When to call a pro
- F9 E1 returns after the hose depth, the tape, the filter and the house drain have all been checked.
- The pump hums or stays silent while the drum stays full of water.
- The drain hose is cracked or leaks where it leaves the back of the washer.
- The standpipe or utility sink overflows when the washer pumps out: that calls for a plumber, not a washer repair.
- Water is pooling under the washer or behind the lower front panel.
What a F9 E1 repair costs
$150–$350
Replacing a drain pump costs $150 to $350 with parts and labor in HomeGuide's 2026 national figures, and a new drain hose $100 to $200. Hose depth, tape and filter fixes cost you nothing. Expect a minimum service fee of $70 to $130 if a technician comes out.
SourceWhat F9 E1 means on a Whirlpool washer
Whirlpool's help pages call F9 E1 a long drain time. The washer tried to empty the tub, and the water left too slowly or not at all before its timer ran out. Front-load pages print the code with a space, top-load and Laundry Tower pages print F9E1, and the meaning is the same.
Maytag's help site, also run by Whirlpool Corporation, lists F9 E1 on its front loaders with the same long drain checks.
Why a hose pushed deeper makes draining slower
It seems backwards, but Whirlpool's top-load page warns that a hose pushed past the elbow into the standpipe can siphon water back into the tub and leave the washer with a slow spin or none at all. The pump does its job, gravity and suction pull some of the water back, and the drain timer runs out. That is why the checks start at the standpipe instead of inside the washer.
Front loader or top loader: where the water gets stuck
Front loaders have two extra places for water to hang up: the drain pump filter, which sits behind the bottom storage drawer on some models, and the small drain holes in the rubber door seal. Whirlpool's F9E1 page for top loaders has no filter step at all. For those washers it limits the owner checks to the drain hose and the drain it empties into.
What a technician will check
- Whether the drain pump starts and moves water, and whether its impeller is jammed or broken.
- The inner hose from the tub to the pump, which can trap small items the filter never sees.
- Power reaching the pump from the washer's control and the wiring in between.
- The pressure sensor that tells the washer the tub has emptied.
What fixed it for other readers
No reader fixes yet. If you cleared F9 E1, tell others what worked.
Reader fixes are shared by visitors and checked for safety, not tested by us.
Questions people ask about Whirlpool F9 E1
Is drn the same as F9 E1 on a Whirlpool washer?
Yes. Whirlpool's top-load help page for drn treats it as the same long drain alert as F9 E1 and gives the same hose checks. Which one you see depends on the model.
How often should I clean the drain pump filter?
Whirlpool's pump filter guide suggests every few months, or sooner depending on how often you wash and how much lint and debris collect.
Can too much detergent cause F9 E1?
It can contribute. Whirlpool says excess suds can slow the spin and bring up error codes, though it does not mention F9 E1 specifically. If the drum is full of foam, treat it as a suds problem first and run a Clean Washer cycle before you look for a drain fault.
Sources
- F9 E1 - Front Load Washer (Whirlpool Product Help, checked November 2, 2026)
- F9E1 - Error Code (Top Load Washer) (Whirlpool Product Help, checked November 2, 2026)
- drn - Error Code (Top Load Washer) (Whirlpool Product Help, checked November 2, 2026)
- F9E1 Error Code (Laundry Tower washer) (Whirlpool Product Help, checked November 2, 2026)
- F9E1 - Error Code - All-In-One Washer Dryer (Whirlpool Product Help, checked November 2, 2026)
- Cleaning the Drain Pump Filter (Front Load Washer) (Whirlpool Product Help, checked November 2, 2026)
- Cleaning the Pump Filter - Front Load Washer (Whirlpool Product Help, checked November 2, 2026)
- Excessive Detergent or Suds (Top Load Washer) (Whirlpool Product Help, checked November 2, 2026)
- F9 E1 - Front Load Washer (Maytag) (Maytag Product Help (Whirlpool Corporation), checked November 2, 2026)
- How Much Does Washing Machine Repair Cost? (2026) (HomeGuide, checked November 1, 2026)
