Whirlpool Washer LF or F8 E1 Code: Long Fill and How to Fix It

Low urgencyUpdated Checked against Whirlpool Product Help

Also shown or searched as: F8 E1, F8E1, Lo FL

LF or F8 E1 on a Whirlpool washer (Lo FL on some front loaders) means the washer is taking too long to fill or is not sensing enough incoming water. Open both taps fully, connect both hoses, clean the inlet screens, and make sure the drain hose is not siphoning water out. If the code returns, book service.

What to try first

Safety: Turn both taps off before you unscrew the supply hoses, and keep a towel and bucket handy for the water left inside them.

  1. 1

    Let the washer pump out first

    Whirlpool says the washer may lock the door or lid and run its pump for several minutes when this code appears. On front loaders, press Power and wait about 10 minutes before you touch the controls; they will not respond until the drain routine ends.

  2. 2

    Open both taps all the way

    Turn the hot and cold supply valves fully open. Both hoses must be connected for the washer to run correctly, even if you mostly wash in cold.

  3. 3

    Check the hose hookup

    Hot (red) goes to the hot inlet and cold (blue) to the cold inlet. Straighten any kinks where the hoses bend behind the washer.

  4. 4

    Clean the inlet screens

    Shut off both taps, put a towel down and unscrew the hoses from the back of the washer. Rinse mineral buildup and debris off the screens in the inlets, or replace them if they are torn, then reconnect and reopen the taps.

  5. 5

    Flush each supply hose

    With a hose off the washer, hold it over a sink or tub and run water through it. Whirlpool says a hose that will not pass a full stream should be replaced.

  6. 6

    Fix a siphoning drain hose

    Keep only 4.5 inches of the drain hose inside the standpipe, held by the U-shaped hose form. Remove any tape so the pipe stays open to air. The top of the standpipe must be at least 39 inches above the floor; any lower and water runs out of the washer by gravity.

  7. 7

    Connect the washer straight to the taps

    If a flood-stop device or flood-safe hose is fitted, replace it with standard fill hoses. Whirlpool recommends a direct connection for full water flow.

Most likely causes of LF

  1. 1. A tap that is off or only partly open (most common)

    The washer was just installed or moved, or someone worked on the plumbing. Whirlpool wants both the hot and cold valves fully open.

  2. 2. Only one supply hose connected, or the hoses swapped (common)

    Only a cold line is hooked up, or the red hose does not run from the hot tap to the hot inlet.

  3. 3. A drain hose that lets water escape while the washer fills (common)

    Water trickles out of the drain hose during the fill. The hose sits too deep in the standpipe, is taped in, or empties into a standpipe that is too short.

  4. 4. Clogged inlet screens or a clogged supply hose (common)

    Grit or white mineral scale covers the small screens where the hoses attach, or water barely trickles through a hose held over a sink.

  5. 5. An anti-flood device on the supply line (less common)

    A flood-stop valve or flood-safe hose sits between the tap and the washer. Whirlpool says these can lower water pressure and cut how much water gets in.

  6. 6. A failed water inlet valve (less common)

    Taps, hoses, screens and the drain hose all check out and both taps run strong, yet the code still comes back.

When to call a pro

  • LF or F8 E1 returns after the taps, hoses, screens and drain hose all check out.
  • Both taps run strong into a bucket, but little or no water reaches the drum.
  • Water keeps trickling into the drum while the washer is off.
  • A hose fitting or the inlet valve leaks at the back of the washer.

What a LF repair costs

$100–$300

HomeGuide's 2026 national price for a washer water inlet valve replacement is $100 to $300 including labor, with the valve itself $20 to $100. Opening a tap, cleaning screens or resetting the drain hose costs nothing; minimum service fees run $70 to $130.

Source

LF, F8 E1 and Lo FL are one fill problem

Whirlpool's top-load help page treats F8 E1 and LF as the same long fill alert: the washer is taking too long to fill. Its front-load pages pair F8 E1 with Lo FL and describe it as the washer not detecting the correct amount of incoming water. The checks are the same for all three.

Maytag's help site, also run by Whirlpool Corporation, carries the same LF and F8 E1 page for its top loaders.

Why a drain hose can cause a fill code

A long fill sounds like a supply problem, yet Whirlpool's top-load LF page starts with the drain hose. If the hose sits too deep, is sealed in with tape, or empties into a standpipe that is too low, water leaves the tub by siphon or gravity while it is still filling. The washer fills and drains at the same time and never reaches the level it is waiting for.

Why a cold-only hookup can trigger LF

Whirlpool says these washers have sensors that check the water supply on both hoses and need water reaching both sides of the inlet valve. If they do not detect both, the control flags a water pressure sensor problem instead of finishing the fill. A laundry room with only a cold line, or a hot tap left closed after plumbing work, is enough to set off the code.

What a technician will check

  • Flow and pressure from the hot and cold taps, which can drop after plumbing work or with a worn shutoff valve.
  • The water inlet valve: whether each side opens when the washer calls for water, and whether it is cracked or blocked.
  • The pressure sensor that reports the water level, and its air hose.
  • Whether water leaves through the drain hose during the fill, which marks a siphon rather than a supply fault.

What fixed it for other readers

No reader fixes yet. If you cleared LF, tell others what worked.

Reader fixes are shared by visitors and checked for safety, not tested by us.

Did you clear LF? Tell the next person what worked.

We publish your first name or initial, the month, and your fix. Nothing else.

Questions people ask about Whirlpool LF

How long should a Whirlpool washer take to fill?

It depends on the cycle. Whirlpool says the Bulky cycle on some top loaders fills in stages while it agitates and can take 10 to 12 minutes, which is normal. Heavy Duty and Bulky Items use more water than Normal, and larger load sizes add more.

The water level looks low. Is that LF?

Not by itself. Whirlpool HE top loaders use less water than older machines, and most cycles rinse with a spray. Extra Rinse or fabric softener switches the rinse to a deep fill, and some models have a Deep Water Wash setting.

Why did F8 E1 show up on a brand-new washer?

Whirlpool says a washer switched on before it was connected to water may lock its door, start a drain cycle and show F8 E1. Connect both hoses, open the taps, let the drain routine finish and start again.

Is LF the same as F9 E1?

No. LF is a fill problem and F9 E1 is a drain problem. A badly placed drain hose can cause either one, which is why Whirlpool's pages for both codes check the drain hose.

Sources