Whirlpool Washer F5 E3 Error Code: Door or Lid Lock Problem

Fix soonUpdated Checked against Whirlpool Product Help

Also shown or searched as: F5E3

F5 E3 on a Whirlpool washer is a door lock error. On front loaders Whirlpool says the door is not locking properly; on top loaders the same kind of lock holds the lid. Close the door or lid firmly, clear clothing or packing from the latch, then unplug the washer for 5 minutes. If F5 E3 returns, book service.

What to try first

Safety: Never force or pry a locked door or lid, and never reach into a drum that is still turning. Unplug the washer before you clean around the latch.

  1. 1

    Open the door or lid and close it firmly

    Open it all the way, then close it with a firm push until it latches. A firm press is enough, with no need to slam it.

  2. 2

    Clear the latch and the opening

    Tuck in anything hanging past the door opening, remove any shipping materials on a new washer, and wipe soap buildup off the latch area with a damp cloth.

  3. 3

    Take out part of an overfull load

    Leave enough room for the clothes to tumble freely. Whirlpool's Laundry Tower page lists reducing the load size as one of its F5E3 fixes.

  4. 4

    Unplug the washer for 5 minutes

    Pull the plug, wait 5 minutes, plug it back in and start a cycle. On Whirlpool's top-load F5E3 page this reset is the only owner step listed.

  5. 5

    If a front-load door stays shut after a cycle, run Drain and Spin

    Whirlpool's front-load door page says to unplug the washer for about 2 minutes, plug it back in and run a Drain and Spin cycle. The door should release when that cycle ends.

Most likely causes of F5 E3

  1. 1. The door or lid is not fully latched (most common)

    Whirlpool notes that a door can look closed without being latched. A sleeve or sock pinched at the edge is the usual giveaway.

  2. 2. Clothing, packing material or soap buildup in the latch (common)

    On a new washer, look for tape or foam left from shipping near the latch. On an older one, look for a film of soap around the latch and the opening.

  3. 3. An overfilled drum pressing on the door (common)

    Clothes push against the glass or stick out past the door opening as you close it, leaving no room for the load to tumble.

  4. 4. A control that needs a reset (common)

    The code appeared once and clears after the washer has been unplugged for 5 minutes.

  5. 5. A failed door lock assembly or door switch (less common)

    The door closes cleanly with nothing in the way, but F5 E3 returns after the reset. Whirlpool's Laundry Tower page names the door switch as the potential cause.

When to call a pro

  • F5 E3 comes back after the door is clear, the load is lighter and the washer has been unplugged for 5 minutes.
  • The door stays locked after a Drain and Spin cycle, with wet clothes or water still inside.
  • The latch, hinge or handle is cracked or bent, or the door or lid no longer lines up with the lock.
  • The washer starts with the door or lid able to open, or the lock never engages at all.

What a F5 E3 repair costs

$100–$300

HomeGuide's 2026 national range for replacing a washer door lock or lid switch is $100 to $300 with labor; the latch part alone runs $20 to $130. Closing the door properly, clearing the latch or a reset costs nothing, and a minimum service fee is $70 to $130.

Source

Door lock or lid lock: what Whirlpool means by F5 E3

Whirlpool titles F5 E3 a door lock error on its front-load, top-load, All-In-One washer dryer and Laundry Tower help pages. On a top loader the lock holds the lid shut during the cycle, so top-load owners can read door as lid.

The pages describe the fault from different sides. The front-load page says the door is not locking properly, the Laundry Tower page points to the door switch, and the All-In-One page files F5E3 under a door lock that will not release. In each case the washer could not confirm the lock position it asked for.

A locked door is not always F5 E3

Some locked doors are normal. Whirlpool top loaders keep the lid locked from the start of a cycle until it finishes. On front loaders with a Fresh Hold cycle, the door stays locked after the wash until you press Cancel. A new front loader can even arrive with the door locked from movement during shipping, according to Whirlpool. None of these is a fault, and none needs a repair.

What a technician will check

  • The door lock assembly: whether it moves the latch, and whether its switch reports locked and unlocked correctly.
  • The door switch the washer uses to confirm the door is shut.
  • The wiring between the lock and the washer's control, including the plug at the door.
  • Hinge and strike alignment, so the latch meets the lock squarely every time.

What fixed it for other readers

No reader fixes yet. If you cleared F5 E3, tell others what worked.

Reader fixes are shared by visitors and checked for safety, not tested by us.

Did you clear F5 E3? Tell the next person what worked.

We publish your first name or initial, the month, and your fix. Nothing else.

Questions people ask about Whirlpool F5 E3

Why won't the front-load door open right after I press Pause?

Whirlpool says the door stays locked while the water level or temperature is high, or while the drum is tumbling or spinning. If the Add a Garment light is off, press Pause/Cancel twice and allow up to five minutes; you will hear a click when it releases.

Do I need a new control board for F5 E3?

Usually not as a first step. Whirlpool's pages point to the door lock and the door switch, not the board. A technician should test the lock, the switch and the wiring before replacing anything more expensive.

Is it safe to keep using the washer after F5 E3 clears?

Yes, if the door or lid now locks at the start of every cycle and stays locked until the end. If the code keeps returning, stop using the washer until the lock has been checked.

Sources