Whirlpool Dishwasher F9 E1 Code: Draining Too Slowly? Fixes
Also shown or searched as: F9E1, F9-E1, 9-1
F9 E1 on a Whirlpool dishwasher is the long drain code: water is leaving too slowly or not at all. Whirlpool's checks are the filters, a kinked or clogged drain hose, a new disposer's knockout plug, food in the disposer, the air gap and suds, then a 30-second power reset. If F9E1 returns, have the drain pump checked.
What to try first
Safety: Switch off and unplug the garbage disposer, or turn off its breaker, before you put a hand or tool into it or take the dishwasher hose off its inlet. Let any water left in the tub cool before you reach in for the filters.
- 1
Rinse both filters
Take out the lower rack. Turn the upper filter assembly a quarter turn counterclockwise and lift it out, then lift the lower filter slightly and pull it forward. Rinse both under running water, using a soft brush for stuck-on soil but never a wire brush or scouring pad. Put them back and make sure the upper assembly locks: Whirlpool says that if it turns freely it is not locked, and the dishwasher should not run without the filters properly installed.
- 2
Follow the drain hose under the sink
Look along the hose from where it comes out from under the dishwasher to where it joins the sink drain or disposer. Straighten any kink, move anything pressing on it, and check that it rises in a high loop under the counter, which Whirlpool says prevents siphoning and backflow into the dishwasher.
- 3
Check a new disposer for its knockout plug
If the dishwasher drains into a disposer that was just installed, Whirlpool says the knockout plug must be removed from the disposer's dishwasher inlet. With the disposer switched off and unplugged, loosen the clamp, pull the hose off and look into the inlet. Whirlpool's method is to knock the plug into the disposer with a hammer and screwdriver and lift it out with needle-nose pliers; the disposer's manual has the details for your model.
- 4
Run the disposer and clear the air gap
Run the disposer to clear any food sitting in it, as Whirlpool suggests. If your sink has an air gap, the small cap beside the faucet, take the cap off and clear it the way its maker describes.
- 5
Get rid of any suds
If foam fills the tub, turn the dishwasher off and give the suds time to settle. Use only detergent made for automatic dishwashers; Whirlpool points out that hand dish soap makes suds and dishwasher detergent does not.
- 6
Cut the power for 30 seconds
Unplug the dishwasher for 30 seconds, or switch off its breaker for 30 seconds if it is hard-wired, then restore power. Resume or restart the cycle and watch whether the tub empties before the next fill.
Most likely causes of F9 E1
1. Food and grease packed into the filters (most common)
Dirty water stands at the bottom of the tub around the filter, and the filters have not been rinsed in a month or more.
2. A kinked, pinched or clogged drain hose (common)
The dishwasher was just installed or pushed back into its opening, or the hose under the sink is bent flat behind bins and bottles.
3. A new garbage disposer with its knockout plug still in place (common)
F9E1 showed up on the first cycles after a disposer was installed or the dishwasher was hooked up to one.
4. Food sitting in the disposer or sink drain, or a blocked air gap (common)
The disposer has not been run since the last meal, the sink itself drains slowly, or water spurts from the air gap cap beside the faucet.
5. Suds from hand dish soap or too much detergent (less common)
Foam fills the tub when you open the door after the code.
6. A jammed or failing drain pump (less common)
The pump hums or stays silent while water sits in the tub, even with the filters, the hose and the disposer clear.
When to call a pro
- F9E1 comes back with clean filters, a straight hose, an open disposer inlet and no foam.
- The drain pump hums or makes no sound at all while the tub stays full.
- The hose is split, or the stretch you need to check runs behind the dishwasher, which means sliding it out of the cabinet.
- The kitchen sink backs up or drains slowly even with the dishwasher off: the house drain needs a plumber.
- F9E1 comes with water leaking from the base of the dishwasher.
What a F9 E1 repair costs
$80–$400
HomeGuide's 2026 national prices with labor: $80 to $180 for a new drain hose, $100 to $400 for a drain pump (the pump alone is $20 to $100) and $80 to $150 to install an air gap. Rinsing filters, straightening the hose and clearing the disposer cost nothing; a visit starts at the $70 to $130 minimum service fee.
SourceWhat F9E1 means on a Whirlpool dishwasher
Whirlpool's help pages give F9E1 a single potential cause, long drain, and its guide to reading codes calls it long drain, not draining. Between fills, the dishwasher tried to pump the used water away and could not get it out properly. The KitchenAid and Maytag help sites, both run by Whirlpool Corporation, give F9E1 the same cause and the same checks.
The next code along, F9E2, is Whirlpool's drain motor error, which points at the pump motor itself. F9E1's checklist, by contrast, is almost all about the path the water takes once it leaves the tub: filters, hose, disposer, air gap.
Why new installs and new disposers set it off
Two of Whirlpool's F9E1 checks only matter after work under the sink. A new disposer has a plastic plug closing its dishwasher inlet, and the dishwasher cannot empty into it until someone knocks that plug out. Whirlpool also asks for the drain hose to be routed correctly, on the correct side of the dishwasher and inside its frame, and warns that a kinked or clogged hose can mean poor drainage or none at all.
Whirlpool's drain line page adds the high loop. The hose should rise up under the counter before it drops to the sink drain or the disposer; without that loop, water can siphon and flow back into the dishwasher.
F9E1 on some older KitchenAid models
Not every F9E1 report is about draining. The owner of a 2017 KitchenAid KDFE104DWH4 on the AppliancePartsPros forum titled the thread 'Diverter valve position cannot be determined', with water leaking at the diverter, the part that switches water between the spray arms. Replacing the diverter motor, a grommet seal and the valve cover did not clear the code. Whirlpool's current help pages list only long drain for F9E1, so if your dishwasher drains normally and still shows it, ask the technician to read the code table on your model's tech sheet.
What a technician will check
- The hose route behind the dishwasher. Whirlpool asks for the drain hose to run on the correct side and inside the frame, with no kinks.
- The drain pump and the sump in front of it, for glass, bones or other debris that stops the impeller.
- Whether the pump gets power from the control when it should, and the wiring between the two.
- On models whose tech sheet ties F9E1 to the diverter rather than to draining, the diverter motor and its seals.
What fixed it for other readers
No reader fixes yet. If you cleared F9 E1, tell others what worked.
Reader fixes are shared by visitors and checked for safety, not tested by us.
Questions people ask about Whirlpool F9 E1
What does a 9-1 flashing light mean on a Whirlpool dishwasher?
On models without a number display, the Clean light spells out codes in two sets of flashes. Nine flashes, a pause and one flash is F9E1, and Whirlpool's page for that pattern gives the same drain checks.
How often should I clean the filters to avoid F9E1?
Whirlpool's filter guide suggests about once a month, and every two weeks for large families or daily use. A rinse under running water is usually enough; save the soft brush for soil that will not wash off.
How much does it cost to fix F9E1?
Often nothing, since filters, hoses and disposer plugs are free to clear. If parts are needed, HomeGuide's 2026 national figures put a drain hose at $80 to $180 and a drain pump at $100 to $400, labor included.
Sources
- F9E1 - Dishwasher (Whirlpool Product Help, checked November 6, 2026)
- 9 Pause 1 Pause - pause, repeat - Error Code - Dishwasher (Whirlpool Product Help, checked November 6, 2026)
- Dishwasher Error Codes - Reading (Whirlpool Product Help, checked November 6, 2026)
- Clean Light Flashing - Dishwasher (Whirlpool Product Help, checked November 6, 2026)
- F9E2 - Dishwasher (Whirlpool Product Help, checked November 6, 2026)
- How to Clean the Dishwasher Filters (Whirlpool Product Help, checked November 6, 2026)
- Drain Line Installation (Whirlpool Product Help, checked November 6, 2026)
- Connecting Dishwasher Drain to Garbage Disposal (Whirlpool Product Help, checked November 6, 2026)
- F9E1 - Dishwasher (KitchenAid) (KitchenAid Product Help (Whirlpool Corporation), checked November 6, 2026)
- F9E1 - Dishwasher (Maytag) (Maytag Product Help (Whirlpool Corporation), checked November 6, 2026)
- F9E1 error code - Diverter valve position cannot be determined (AppliancePartsPros forum, checked November 6, 2026)
- How Much Does Dishwasher Repair Cost? (2026) (HomeGuide, checked November 5, 2026)
