Whirlpool Dishwasher F4 E3 Code: Heating Error, What to Do
Also shown or searched as: F4E3, F4-E3, 4-3
F4 E3 on a Whirlpool dishwasher is a heating error, according to Whirlpool's help pages. The only home step Whirlpool gives is to cut the power for 30 seconds, by unplugging the dishwasher or switching off its breaker. If F4E3 comes back, Whirlpool says to schedule service; the heater and its parts are a technician's job.
What to try first
Safety: Leave the heater, its sensors and the wiring to a technician: testing them means working under the tub with the power off at the breaker. If the breaker trips or you smell burning, keep the dishwasher switched off until it has been checked.
- 1
Cut the power for 30 seconds
Unplug the dishwasher, or turn off its breaker at the electrical panel if it is hard-wired. Wait 30 seconds and restore power. This reset is the only home step on Whirlpool's F4E3 page.
- 2
Run the kitchen tap hot before the next cycle
Run the faucet nearest the dishwasher until the water comes out hot, then start the cycle. Whirlpool's dishwashers do best with incoming water at 120°F, so if the tap never gets properly hot, check that your water heater is set to at least 120°F. Whirlpool does not name cold water as a cause of F4E3, but this check costs nothing.
- 3
Watch and listen during the next cycle
Notice whether you hear water spraying once it has filled, and whether the dishes are hot when the cycle ends. Tell the technician what you saw and when the code appeared: it helps separate a heating fault from a wash motor fault.
Most likely causes of F4 E3
1. The dishwasher's heater has failed (common)
The dishes and the inside of the door are cool at the end of cycles that used to finish hot, and the code returns after a reset.
2. A one-off electronic fault (common)
The code clears after 30 seconds without power and does not return over the next few loads.
3. On some models, the wash motor or its link to the control (common)
The dishwasher fills and drains but you never hear water spraying, which is how owners on iFixit and the AppliancePartsPros forum describe their 4-3 code.
4. A fault in the heater's wiring, its temperature sensor or the control that switches it (less common)
A technician finds that the heater itself tests fine, yet F4E3 keeps coming back.
When to call a pro
- F4E3 returns after the power reset. Whirlpool's page says to schedule service at that point.
- Dishes come out cold and wet even on cycles that end without a code.
- The dishwasher fills and drains but does not wash.
- The breaker trips, or you smell something hot or burning. Leave the dishwasher off until it has been checked.
- Finding the fault means testing the heater, its sensors or the wiring under the tub with a meter.
What a F4 E3 repair costs
$200–$600
HomeGuide's 2026 national figures, parts and labor: $200 to $350 for a new heating element (the part alone is $25 to $75) and $200 to $600 to repair a control board. If the technician traces the code to the wash motor instead, a new motor is $350 to $500. HomeGuide does not price a thermistor or a high-limit thermostat on its own; a visit starts at the $70 to $130 minimum service fee.
SourceWhat F4E3 means on a Whirlpool dishwasher
Whirlpool's help page lists one potential cause for F4E3, a heating error, and one fix, a power reset, followed by a service call if the code returns. The KitchenAid and Maytag help sites, also run by Whirlpool Corporation, give the same cause and the same step. F4E2, the code just before it, is listed as a heating system fault with the same reset-then-service advice.
The page does not say which part failed. Whirlpool's water temperature pages explain what is at stake: most of its models use an internal heater to raise the water temperature, and the cycle pauses two to three times for thermal holds, moving on only once the water is hot enough.
Heating error or wash motor? Owners' reports differ
Not every owner who sees this code has a heating problem. On iFixit, the owner of a Whirlpool WDTA50SAHZ0 got a 4-3 code on a dishwasher that filled and drained but would not wash, and the top answer called F4-E3 a communication error between the control and the circulation pump motor. On the AppliancePartsPros forum, a WDF330PAHW1 owner read 4-3 as a wash motor code and replaced the motor, the control and the wiring without clearing it.
Whirlpool's current help pages put the wash motor under a different code, F7E2. Whichever reading applies to your dishwasher, both owners above replaced costly parts and still had the code. Ask the technician to confirm what F4E3 means on your model's tech sheet, and to test before ordering anything.
Hot water and the heater
Whirlpool says its dishwashers perform best with incoming water at 120°F, and that the inlet should be connected to the home's hot water line with the valve fully open. When a dishwasher is fed cold water, Whirlpool warns that the internal heater may not reach the needed temperature within the standard cycle time. It does not link F4E3 to cold water, so treat the tap check as a free first look, not the fix.
What a technician will check
- The code table on the model's tech sheet, to confirm what F4E3 or a 4-3 blink covers on that dishwasher before any part is ordered.
- The heater and its connections, tested with the power off.
- The temperature sensor and any high-limit thermostat that protects the heater.
- The circulation (wash) motor and its wiring harness, if the dishwasher fills but does not wash.
- Whether the control needs a reset after a heater has been replaced. One owner on the AppliancePartsPros forum found that the control had stopped powering a new element until it was reset from the keypad.
What fixed it for other readers
No reader fixes yet. If you cleared F4 E3, tell others what worked.
Reader fixes are shared by visitors and checked for safety, not tested by us.
Questions people ask about Whirlpool F4 E3
What does a 4-3 flashing light mean on a Whirlpool dishwasher?
On models with no number display, the Clean light flashes codes in two sets: the first set is the F number and the second the E number. Four flashes, a pause and three flashes is F4E3.
Can I keep using my Whirlpool dishwasher with F4E3?
If the code cleared after the reset and the dishes come out hot and clean, yes, but keep an eye on it. If F4E3 returns, Whirlpool's advice is to schedule service rather than keep resetting it.
How much does it cost to fix F4E3?
It depends on the part. HomeGuide's 2026 national figures put a new heating element at $200 to $350 with labor and a control board repair at $200 to $600. A visit that ends with nothing but a reset costs the $70 to $130 minimum service fee.
Sources
- F4E3 - Dishwasher (Whirlpool Product Help, checked November 6, 2026)
- F4E3 - Dishwasher (KitchenAid) (KitchenAid Product Help (Whirlpool Corporation), checked November 6, 2026)
- F4E3 - Dishwasher (Maytag) (Maytag Product Help (Whirlpool Corporation), checked November 6, 2026)
- F4E2 - Dishwasher (Whirlpool Product Help, checked November 6, 2026)
- F7E2 - Dishwasher (Whirlpool Product Help, checked November 6, 2026)
- Clean Light Flashing - Dishwasher (Whirlpool Product Help, checked November 6, 2026)
- Dishwasher Water Temperature Troubleshooting (Whirlpool Product Help, checked November 6, 2026)
- Water Temperature - Dishwasher (Whirlpool Product Help, checked November 6, 2026)
- SOLVED: Dishwasher will fill but won't wash error code 4-3 (Whirlpool WDTA50SAHZ0) (iFixit Answers, checked November 6, 2026)
- Whirlpool Dishwasher Not Circulating Water (AppliancePartsPros forum, checked November 6, 2026)
- Whirlpool dishwasher won't heat (AppliancePartsPros forum, checked November 6, 2026)
- How Much Does Dishwasher Repair Cost? (2026) (HomeGuide, checked November 5, 2026)
