Whirlpool Dishwasher F8 E4 Error Code: Water in Drip Tray
Also shown or searched as: F8E4, F8-E4, 8-4
F8 E4 on a Whirlpool dishwasher means the float switch has found water in the drip tray under the tub. Whirlpool's advice: turn off the dishwasher's water supply, press Cancel once, and leave the power on with the door closed so it can drain. Then check for suds and leaks; the tray itself is a technician's job.
What to try first
Safety: Whirlpool asks you to keep the power on while F8E4 drains, so do not reach under the dishwasher or stand in water next to it during that time. If water has spread across the floor or reached the outlet or wiring in the sink cabinet, switch off the dishwasher's breaker first and mop up afterwards. Leave the kick plate and the drip tray to a technician.
- 1
Turn off the water, silence the alarm, keep the power on
Close the valve that feeds the dishwasher, usually under the kitchen sink. Press Cancel once to stop the alarm tone. Whirlpool says not to turn off the power and to keep the door closed: the dishwasher starts a drain sequence and blocks any further cycles while the code is active.
- 2
Mop up and note where the water is
Dry the floor in front of the dishwasher and the floor of the sink cabinet. Note where water shows up: under the door, on the sink cabinet side, or from under the middle of the machine. A technician will ask.
- 3
Look for suds once it has drained
Open the door after the drain has run. If foam is inside, Whirlpool's leaking page says to remove the dishes, pour about 1/4 cup of vegetable or other cooking oil into the bottom of the tub and run a Quick cycle with no detergent and no dishes, repeating until the suds are gone. From then on use only detergent made for automatic dishwashers: Whirlpool notes that dish soap makes suds and dishwasher detergent does not.
- 4
Check the hose connections you can see under the sink
Wipe the dishwasher's supply valve and the spot where the drain hose joins the disposer or sink drain with a paper towel, then look again a few minutes later and during the next drain. Whirlpool asks you to verify that the drain hose is properly connected. A drip from the valve itself is a plumbing repair.
- 5
Clear the code with Cancel
With the tub drained and the floor dry, press Cancel once to silence the tone and a second time to clear F8E4, as Whirlpool describes. Turn the water back on and stay close for the first few minutes of the next cycle. If the code comes straight back, water is still sitting in the drip tray.
Most likely causes of F8 E4
1. A loose water supply connection under the dishwasher (most common)
The dishwasher was installed or moved in the last few days and the code came up on one of its first cycles. Whirlpool's F8E4 page opens with exactly this case.
2. Suds from hand dish soap or too much detergent (common)
Foam fills the tub or rims the door when you open it, or someone used hand dish soap or a double dose of detergent.
3. A drain hose that is not properly connected (common)
Drips appear at the hose clamp under the sink while the dishwasher pumps out, or the hose has slipped partway off its fitting.
4. A float switch left unplugged during an install or repair (less common)
The code appeared right after work on the dishwasher, yet the floor is dry and there is no foam in the tub.
5. A worn pump, diverter or motor shaft seal (less common)
Water turns up under the center or rear of the machine again after the tray has been dried, with no suds and dry fittings.
6. A one-off splash or condensation (less common)
Once the tray has been dried, the code stays away for good and nothing drips anywhere.
When to call a pro
- F8 E4 returns after Cancel. The drip tray still holds water, and Fred's Appliance says reaching it means unscrewing the kick plate below the door, then easing the tray out with its float switch wire still attached.
- The dishwasher was installed in the last few days. Ask the installer to recheck the water fitting under the machine, the first item on Whirlpool's F8E4 page.
- Water keeps reaching the floor, or it appears under the middle or back of the dishwasher.
- The dishwasher's water valve will not close, or it drips. For a fill that will not stop (its F8E5 code), Whirlpool's advice is to turn the power off instead when the water cannot be shut off.
- The code shows up with a dry floor, no suds and nothing dripping under the sink.
What a F8 E4 repair costs
$80–$190
What you pay depends on what leaked. HomeGuide's 2026 national ranges with labor: $80 to $170 for a new water inlet valve, $80 to $180 for a drain hose and $90 to $190 for a float switch. If the visit ends with a reseated fitting or an emptied tray, expect the minimum service fee of $70 to $130. A suds spill costs nothing.
SourceWhat F8E4 means on a Whirlpool dishwasher
Whirlpool's guide to reading dishwasher codes lists F8E4 as water detected in the drip tray. The tray is a plastic pan at the very bottom of the machine, under the tub, with a float switch in it. Water that escapes the tub, a fitting or a hose ends up there, the float rises and the dishwasher stops. Whirlpool files the same F8E4 article under its error codes and under leaks underneath or behind the dishwasher, and the KitchenAid and Maytag help sites carry the same steps.
Models without a number display show the code with a flashing light. Whirlpool's help site explains how to read it: the first set of flashes is the F number and the second set is the E number. Eight flashes, a pause and four flashes is F8E4, and Whirlpool's page for that pattern gives the same checks.
Why Whirlpool says to leave the power on
Whirlpool's guide to reading dishwasher codes resets the control panel by cutting its power for 30 seconds, and that power cycle is the first step it gives for several codes. F8E4 is the exception. Whirlpool's page says the drain sequence will begin and the machine will not run, and asks you to turn the water off, press Cancel once and keep the power on with the door closed. Switching the power off would stop that drain.
Whirlpool gives the same routine for F8E5, a fill valve stuck open, with one addition: if you are unable to turn the water supply off, turn off the power to the dishwasher instead.
F8E4 right after an installation
Whirlpool's F8E4 page starts by asking whether the dishwasher was recently installed, and most of its checks are installer work under the machine: the rubber washer seated in the water fitting, the elbow tightened without cross-threading, the fill hose leaving at the rear left, the float switch plugged in, and the power cord kept clear of the motor and the bottom of the tub. If someone else installed the dishwasher, those checks are theirs to make, and a recent install is the first thing to mention when you book a visit.
When there is no leak to find
Not every F8E4 means a broken part. Fred's Appliance notes that water can collect in the base pan with no leak at all, for example from condensation or during cleaning, and that over-sudsing can push water out of the tub. If the tray is dried, the detergent is right and the code stays away over the next few loads, nothing more needs fixing. If it comes back, the water is getting out somewhere, and the tray, the fittings and the seals need a closer look.
What a technician will check
- The drip tray: emptied and dried, and the float switch connector pushed in until its locking tab shows over the back of the connector, as Whirlpool's page describes.
- The supply connection at the inlet valve: the rubber washer seated, the 3/4-inch 90-degree elbow hand-tightened to avoid cross-threading and then given a further 1/4 to 1/2 turn with pliers, and the fill hose routed out the rear left side.
- That the power cord does not touch the dishwasher motor or the bottom of the tub, a check Whirlpool lists next to the float switch.
- The pump, diverter and motor shaft seals, which Whirlpool's leaking guide suspects when water pools under the center or rear.
- Both ends of the drain hose and their clamps.
What fixed it for other readers
No reader fixes yet. If you cleared F8 E4, tell others what worked.
Reader fixes are shared by visitors and checked for safety, not tested by us.
Questions people ask about Whirlpool F8 E4
Can I keep using my Whirlpool dishwasher with F8E4 showing?
No. Whirlpool's page says the machine will not run while the code is active, and running more water through a leak only puts more of it under your cabinets. Find the source first, or at least rule out suds and the connections under the sink.
Does F8E4 mean the float switch is broken?
Usually not. The float switch only reports water in the tray, and Whirlpool's checks are about where that water came from. The switch itself becomes a suspect when the tray is dry, its connector is seated and the code still appears.
How much does it cost to fix F8E4 on a Whirlpool dishwasher?
Nothing if suds caused it. With a technician, HomeGuide's 2026 national figures run from the $70 to $130 minimum service fee for a reseated fitting to $90 to $190 for a new float switch, with a water inlet valve at $80 to $170.
Sources
- F8E4 - Dishwasher (Whirlpool Product Help, checked November 6, 2026)
- F8E4 - Error Code - Dishwasher (Leaking, underneath or behind) (Whirlpool Product Help, checked November 6, 2026)
- 8 Pause 4 Pause - pause, repeat - Error Code - Dishwasher (Whirlpool Product Help, checked November 6, 2026)
- Dishwasher Error Codes - Reading (Whirlpool Product Help, checked November 6, 2026)
- Clean Light Flashing - Dishwasher (Whirlpool Product Help, checked November 6, 2026)
- F8E5 - Dishwasher (Whirlpool Product Help, checked November 6, 2026)
- Leaking - Underneath - Dishwasher (Whirlpool Product Help, checked November 6, 2026)
- Dishwasher Leaking Troubleshooting Guide (Whirlpool Product Help, checked November 6, 2026)
- F8E4 - Dishwasher (KitchenAid) (KitchenAid Product Help (Whirlpool Corporation), checked November 6, 2026)
- 8 Pause 4 Pause - pause, repeat - Error Code - Dishwasher (Maytag) (Maytag Product Help (Whirlpool Corporation), checked November 6, 2026)
- How to Fix a Whirlpool Dishwasher F8 E4 Error Code (Fred's Appliance, checked November 6, 2026)
- How Much Does Dishwasher Repair Cost? (2026) (HomeGuide, checked November 5, 2026)
