LG Dryer Error Code tE1: Thermistor Fault, Reset and Fix

Fix soonUpdated Checked against LG USA Support

LG dryer error code tE1 means the dryer has detected a problem with its thermistor, a temperature sensor. LG's first fix is a reset: unplug the dryer or switch off its breaker, hold Start/Pause for 5 seconds, restore power and run another cycle. If tE1 comes back after that, LG says the dryer may need repair service.

What to try first

Safety: Unplug the dryer or switch off its breaker before the reset. Testing the thermistor, its wiring or the control board means opening the cabinet: leave that to a technician.

  1. 1

    Check the code is tE1, not tE2

    Read the display closely. LG gives tE2 its own steps for cold weather and steam cycles, while tE1 goes straight to a reset and, if needed, service.

  2. 2

    Cut the power

    Unplug the dryer from the wall outlet or switch off its circuit breaker. LG's reset starts with the dryer fully without power.

  3. 3

    Hold Start/Pause for 5 seconds

    With the power still off, press and hold Start/Pause for 5 seconds. LG Canada calls this whole routine a factory reset.

  4. 4

    Restore power and run a cycle

    Plug the dryer back in or switch the breaker on, then start another cycle and watch whether tE1 returns.

  5. 5

    Keep the lint filter clean and the vent flaps free

    For its other thermistor code, tE2, LG asks owners to clean the lint filter and confirm the outside vent flaps open fully while the dryer runs. Both checks are worth doing before you book a visit.

Most likely causes of tE1

  1. 1. A faulty thermistor (most common)

    tE1 comes back after LG's reset, often within seconds of starting a cycle, and the dryer stops or will not heat.

  2. 2. A one-off control glitch that a reset clears (common)

    tE1 showed up once, the reset cleared it, and the next few loads dry normally with no code.

  3. 3. Damaged wiring or a loose connector on the sensor circuit (common)

    The code persists even with a new thermistor fitted, or it comes and goes as the dryer moves and vibrates.

  4. 4. Overheating from a restricted exhaust vent (common)

    Loads take longer to dry, the dryer or the laundry room feels hotter than usual, or you notice a hot smell along with the code.

  5. 5. A faulty main control board (less common)

    The thermistor and its wiring test good, the vent is clear, and tE1 still shows on every cycle.

When to call a pro

  • tE1 comes back after LG's reset. LG says the unit may then require repair service.
  • The dryer shuts off within seconds of starting, or will not heat, every time tE1 shows.
  • The dryer runs very hot or you smell something hot or burning. Dryer Geeks advises stopping use until the problem is diagnosed.
  • A new thermistor has already been fitted and tE1 is still there.
  • You have a gas dryer and suspect a gas supply problem; leave the gas side to a qualified technician.

What a tE1 repair costs

$70–$130

HomeGuide's 2026 national minimum service fee, which covers the first hour of a visit; LG's reset costs nothing. HomeGuide prices no thermistor replacement, so no part figure is used. If a technician finds the control board at fault, HomeGuide lists that repair at $250 to $500.

Source

tE1, tE2 and tE3 on an LG dryer

LG lists several tE codes, and they are easy to mix up. LG's US error code list says a tE1 code indicates a problem was detected with the dryer's thermistor, and its answer is a reset followed by service if the code returns. LG uses the same wording and the same steps for tE3.

tE2 is the odd one out. LG describes it as a thermistor problem that normally happens in cold conditions, when the duct cools down too quickly, and it can show during SteamFresh or other steam cycles. Its fix is about the vent and the cycle, not a failed part. LG also lists a TE4 code that it says will require service.

What LG means by a factory reset for tE1

People search for a factory reset for tE1 because LG Canada uses that phrase: it says the fix is usually a simple factory reset. There is no hidden menu involved. It is the same power reset LG gives for a PF code: unplug the dryer or trip the breaker, hold Start/Pause for 5 seconds, restore power and run a cycle.

That reset can only clear a one-time glitch. If the thermistor or its wiring has really failed, tE1 comes straight back, which is LG's signal that the dryer needs a repair visit rather than more resets.

tE1 after replacing the thermistor

A new thermistor does not always clear the code. In an AppliancePartsPros forum thread, the owner of an LG dryer replaced the thermistor and the code stayed. They checked continuity from the thermistor to the harness at the control board, ran new wires, and swapped several other parts before trying a new control board.

Even that first board did not fix it. The poster later found the replacement board itself was faulty, and a second board finally cleared tE1. The lesson is to test the wiring and the board methodically rather than keep swapping parts, which is the order Dryer Geeks also suggests once the vent is ruled out.

Can a blocked vent cause tE1?

LG's tE1 entry does not mention the vent. Dryer Geeks, a dryer vent service company, argues that restricted airflow can make the dryer run hot, so the sensor may simply be reporting real overheating. Signs it lists include longer drying times, a hotter dryer, extra humidity and a hot smell.

Its advice is to check the vent first. If the vent is clear and tE1 remains, Dryer Geeks says a sensor, harness or board issue becomes more likely. A lint check costs nothing, so it is worth doing before paying for parts.

tE1 on an LG gas dryer

LG's tE1 instructions do not single out gas models; the thermistor reset and the advice to call for service are the same. A gas supply problem shows as a different message: LG's error code list for its East Africa site describes a gAS code, meaning the dryer is not receiving gas. If you see tE1 on a gas dryer, treat it as a sensor fault and leave any gas line work to a technician.

What a technician will check

  • The thermistor itself, tested with a meter against the value for your model.
  • Continuity in the wiring from the thermistor to the harness that plugs into the control board, including the connectors at both ends.
  • Airflow through the lint filter housing, exhaust hose and wall duct, so the sensor is not reacting to real overheating.
  • The main control board, checked last once the thermistor, wiring and vent are proven good.

What fixed it for other readers

No reader fixes yet. If you cleared tE1, tell others what worked.

Reader fixes are shared by visitors and checked for safety, not tested by us.

Did you clear tE1? Tell the next person what worked.

We publish your first name or initial, the month, and your fix. Nothing else.

Questions people ask about LG tE1

How do I reset error code tE1 on my LG dryer?

Unplug the dryer or switch off its breaker, hold Start/Pause for 5 seconds, then restore power and start a cycle. That is LG's reset for tE1. If the code returns on the next cycle, a reset will not fix it and the dryer may need service.

Is the tE1 error code a control board problem?

Usually not first. LG ties tE1 to the thermistor, and the wiring between the sensor and the board is a common suspect too. The control board is the last thing to check, after the thermistor and its harness test good.

Can I keep using my LG dryer with a tE1 code?

The dryer may stop the cycle or limit how it runs while tE1 is showing. Dryer Geeks says it is best to stop using it until the issue is diagnosed, especially if the dryer seems to be running hot.

How much does it cost to fix tE1 on an LG dryer?

The reset is free. HomeGuide puts a minimum service fee at $70 to $130 for the first hour, and it does not list a thermistor repair. A control board, if that turns out to be the cause, runs $250 to $500 on its list.

Sources