LG Dryer Error Code d80: Vent Blockage, Flow Sense Fix
Also shown or searched as: d90, d95
LG dryer error code d80 means the Flow Sense system has found about 80% restriction in the exhaust airflow; d90 and d95 mean worse blockage. Clean the lint filter, then check the exhaust hose, wall duct and outside vent flap for lint, kinks or crushing. The code can take several cycles to clear after airflow improves.
What to try first
Safety: Unplug the dryer before you reach behind it or disconnect the exhaust hose. On a gas dryer, leave the hose and duct work to a professional.
- 1
Clean the lint filter
Pull the filter out and roll the lint off with your fingers. If a film is left on the mesh, wash it with soap and water, let it dry completely and push it back in firmly. LG asks for this before every load.
- 2
Check the hose behind the dryer
Unplug the dryer first. Look at the exhaust hose and the duct behind it: it should not be crushed, dented, kinked, coiled like a spring, torn or loose at the joints. Straighten it and leave a little room between the dryer and the wall.
- 3
Watch the outside vent while the dryer runs
Run the Air Dry cycle and go outside. The flaps on the vent hood should open all the way. Clear any lint around the opening, and make sure a pest guard or cap is not holding the flaps shut.
- 4
Clear the hose and the wall opening
With the dryer unplugged, disconnect the exhaust hose, remove lint from the hose and as far into the wall duct as you can reach, then reconnect it. On a gas dryer, LG suggests leaving this to a professional.
- 5
Dry smaller loads
LG lists load size as one of its checks. A packed drum slows the airflow, so split big loads while you sort out the vent.
- 6
Unplug for five minutes, then run a test cycle
If d80 is still showing after the vent is clear, unplug the dryer for five minutes, plug it back in and run a cycle. Give it a few consecutive loads: on some models Flow Sense needs several cycles to confirm the better airflow before the code goes away.
Most likely causes of d80
1. Lint packed in the filter, exhaust hose or wall duct (most common)
Loads take longer to dry or need a second cycle, and you find lint in the filter housing, the hose behind the dryer or the duct opening in the wall.
2. A crushed, kinked or coiled exhaust hose behind the dryer (common)
The dryer was pushed back against the wall recently, or the hose is dented, squashed flat, bunched up like a spring or has holes and loose joints.
3. An outside vent flap that will not open fully (common)
With the dryer running, the flaps on the outside hood stay shut or barely move, or lint, a nest or a pest cover is sitting over the opening.
4. A duct run that is too long or has too many bends (common)
The vent travels a long way through walls, ceilings or up to the roof, and the code keeps coming back even after the parts you can reach are clean.
5. Low gas supply on a gas model (less common)
You have a gas dryer, the vent path checks out clear, and the load runs without drying properly.
6. A fault inside the dryer (less common)
The whole vent path has been cleaned and checked, yet d80 or a higher code keeps showing over several cycles.
When to call a pro
- The duct runs inside walls or ceilings, goes up to the roof, or is too long to clean from either end. LG recommends a professional dryer vent cleaner for this.
- You see d95. LG says to stop using the dryer until the vent path has been inspected and cleared.
- You smell burning. Stop the dryer and have the dryer and the vent inspected.
- You have a gas dryer and d80 stays after the vent is clear, since LG says the code can mean a lack of gas reaching the dryer.
- The whole vent path has been checked and cleaned and d80 still keeps coming back over several cycles. LG points you to its support team at that stage.
What a d80 repair costs
$80–$185
HomeGuide's 2026 national range for cleaning a clogged dryer vent, which is the fix LG points to for d80. Clearing the filter, hose and outside flap yourself costs nothing. A crushed duct that has to be replaced runs $100 to $300, and a minimum service fee is $70 to $130. HomeGuide lists no price for a Flow Sense or sensor fault.
Sourced80, d90 and d95: one warning at three levels
LG's Flow Sense system watches how freely hot, damp air leaves the dryer. LG's US error code list ties each code to a level of restriction: d80 is about 80%, d90 about 90% and d95 about 95%, and the same list also shows a d75. So the three codes are one problem getting worse, which is why they share this page and the same fix.
The number matters most at the top end. LG Canada says a d95 means you should stop using the dryer until the vent path has been inspected and cleared. At d80 and d90 you may notice longer drying times, a hotter dryer or loads that need a second cycle. Repair guides from Fred's Appliance Academy and RemoveAndReplace add that the dryer may switch itself off and beep.
One thing to watch on LG's own list: D90 also appears there as a washer code with a different meaning, a temporary dry function error. If your machine washes and dries in one drum, check the washer codes for your model too.
Why d80 is still there after cleaning the vent
LG's answer here is patience. LG Canada says the indicator may take multiple cycles to reset after airflow improves, and the timing varies by model. A single test load right after cleaning is often not enough to clear it.
If several loads go by and the code stays, the restriction is usually somewhere you did not reach. Commenters on RemoveAndReplace and the North London Appliance Repairs forum describe a roof cap too small for the duct, a 25-foot duct that needed cleaning end to end, and a code that only dropped from d90 to d80 after a new duct and outdoor vent. LG also warns that foil or plastic ducting can restrict airflow and trap lint where your instructions call for metal duct.
d80 with no blockage you can find
Some owners clean everything and still see d80. The test repair sites suggest is simple: with the exhaust hose disconnected from the back of the dryer, run a wet load. RemoveAndReplace says that if the clothes dry in normal time, the problem is in the exhaust system; if they come out wet, a heating element or thermal fuse may be at fault instead.
Whether the code shows partway through a load or at the end of a cycle, LG's steps are the same, and LG says not to open internal components to hunt for a sensor or a blockage. Once the full vent path is confirmed clean and the warning stays, LG's advice is to contact its support team for service.
d80 on an LG gas dryer
Gas models add one cause the electric ones do not have. LG's US error code list notes that on gas dryers a d80 code may indicate a lack of gas supplied to the unit. LG Canada puts it the same way and says to use a qualified professional for a gas dryer. Check the vent first, then leave the gas side to a technician.
What a technician will check
- The full length of the duct from the dryer to the outside and the number of 90-degree bends, compared with the installation instructions for your model.
- The duct inside the walls and the roof or wall cap, cleaned with long brushes, including any screen or undersized cap that traps lint.
- A test run with the exhaust hose off the back of the dryer. If a wet load dries in normal time, the restriction is in the vent; if it stays wet, the heating element or thermal fuse is next.
- The gas supply to the dryer on gas models.
- Whether the dryer itself is misreading the airflow once the vent is proven clear, which needs the cabinet opened.
What fixed it for other readers
No reader fixes yet. If you cleared d80, tell others what worked.
Reader fixes are shared by visitors and checked for safety, not tested by us.
Questions people ask about LG d80
How do I disable D80 on my LG dryer?
LG's pages give no setting to switch Flow Sense or the d80 code off. LG Canada says to treat d80 as an airflow alert and clean the full exhaust path rather than dismiss the message. Once airflow is back, the code clears by itself over a few cycles.
How do I reset the d80 sensor on my LG dryer?
There is no separate sensor reset. LG's reset for d80 is to unplug the dryer for five minutes, plug it back in and run a test cycle. Fred's Appliance Academy also suggests turning the dryer off and on once the vent is clear.
Why is the Flow Sense light showing bars on my LG dryer?
The Flow Sense indicator on the panel reports how restricted the exhaust is. LG's US error code list says two or four bars mean the exhaust system is severely restricted, so the vent needs the same checks as a d80 code.
Where is the d80 sensor on an LG dryer?
LG does not give the location of its Flow Sense parts, and it says not to open internal components to look for a sensor or a blockage. Every check LG lists is outside the cabinet: the lint filter, the exhaust hose, the wall duct and the outside vent.
Sources
- LG Dryer - Error Code List (LG USA Support, checked November 16, 2026)
- Flow Sense WARNING! - d80 / d90 / d95 message (LG Canada Support, checked November 16, 2026)
- Clearing d80 notification code from display panel (LG Canada Support, checked November 16, 2026)
- How to Fix LG Dryer Error Codes D80, D90, and D95 (Fred's Appliance Academy, checked November 16, 2026)
- LG Dryer Error Codes D80 D90 D95 - How To Clear The Error Code? (RemoveAndReplace, checked November 16, 2026)
- How to clear LG Dryer error codes D80 D90 D95? (North London Appliance Repairs, checked November 16, 2026)
- How Much Does Dryer Repair Cost? (2026) (HomeGuide, checked November 6, 2026)
