LG Dishwasher Error Code LE: Motor Error, Reset and Fix

Fix soonUpdated Checked against LG USA Support

LG dishwasher error code LE means the wash motor is not working normally, either a fault in the motor or in the wiring harness between the motor and the control board. To reset it, press Power to turn it off, switch off its breaker for 10 seconds, restore power and run another cycle. If LE returns, it needs service.

What to try first

Safety: Switch the dishwasher off at the breaker before anyone works on it. The sump, the wash motor, its wiring and the door harness are for a technician; do not open the base or the door panels yourself.

  1. 1

    Turn the dishwasher off

    Press the Power button so the dishwasher shuts down. Leave the door closed while you go to the breaker panel.

  2. 2

    Switch off the breaker for 10 seconds

    Trip the circuit breaker that feeds the dishwasher, wait at least 10 seconds, then switch it back on. This is the reset LG gives for LE.

  3. 3

    Run another cycle

    Turn the dishwasher on and start a normal cycle. Stay nearby for the first few minutes and listen for the wash to start. If it runs through and the dishes come out clean, nothing more needs doing for now.

  4. 4

    Book service if LE shows again

    LG says a dishwasher that shows LE again after the reset needs a service technician. Turn it off and leave it until then rather than restarting it over and over.

Most likely causes of LE

  1. 1. The wash motor has failed or shorted (most common)

    LE comes back after every breaker reset, and a technician finds the chopper and motor shaft spin freely with nothing caught in the pump.

  2. 2. A loose or damaged wiring harness between the motor and the control board (common)

    LE shows on some cycles and not others, or it started after the door, panels or the dishwasher itself had been moved or worked on.

  3. 3. Something wrapped around the motor shaft or stuck in the pump (common)

    A technician finds string, a glass chip or other debris in the sump that stops the impeller or the chopper from turning freely.

  4. 4. A one-off electronic glitch (less common)

    LE clears after the power has been off and stays away over the next few full cycles.

  5. 5. A faulty main control board (less common)

    The motor, the harness and the pump all test fine, yet LE keeps showing.

When to call a pro

  • LE comes back after the breaker reset. LG says the unit then needs service.
  • LE comes and goes from cycle to cycle, which can point at a loose wire in the harness.
  • You suspect glass or another object fell into the bottom of the tub and went into the pump, since reaching the pump means taking the sump apart.
  • Checking the motor wiring, which runs under the tub and behind the base panel, or testing the motor or the control board.

What a LE repair costs

$350–$500

LG names the motor as the cause, and HomeGuide's 2026 national list prices a dishwasher motor replacement at $350 to $500 with parts and labor. If the fault is only a loose or chafed wire in the harness, HomeGuide does not price that repair; the minimum service fee of $70 to $130 covers the first hour. A control board repair runs $200 to $600 on the same list.

Source

What LE means on an LG dishwasher

LG's US guide to dishwasher error codes says LE may appear when the cleaning motor is not working normally, and it lists no home fix: it asks you to request service. LG's support page for the United Arab Emirates goes a little further. It calls LE a motor error, adds that the problem can sit in the motor or in the wiring harness that joins the motor to the control board, and gives one reset: power off, the breaker off for 10 seconds, then another cycle.

That makes LE different from the drain, fill, leak and suds codes on the same display. Those come with things to clean or straighten. LE does not, because the parts involved sit inside the sump and under the tub.

Not the same LE as on an LG washer

People often search the washer and dishwasher codes together, since both show LE and both point at a motor. On a washer, the motor turns the drum full of clothes. A dishwasher has no drum. Its wash motor drives the pump impeller that pushes water to the spray arms, so a heavy load of dishes is not what stops it.

LG keeps a separate code, nE, for an impeller that does not spin normally, and for that one LG suggests rearranging the dishes and restarting. LE gets no such step. If your display shows nE, the dish-loading advice applies; if it shows LE, go straight to the breaker reset.

What repair threads found inside the pump

In a thread on the AppliancePartsPros forum, an owner with an LDF7932ST found string wrapped around the motor shaft. Cleaning it out did not stop the code from coming back, and the technician's advice was to check that the chopper and shaft spin freely, then replace the motor if they do. On iFixit, an answer from 2026 points to a glass fragment caught in the pump vanes.

Another iFixit answer lists wiring as the most frequent reason for LE, ahead of a locked impeller, a locked rotor or a faulty main board. One owner there said unplugging for 30 seconds cleared it, while another found a 10-second breaker reset did not help. A reset is worth one try, not five.

Older LG models and the door wiring

On Appliantology, a 2013 post about LG dishwashers built from 2004 through mid-2008, starting from an LDF6810ST thread, traced LE to a wash motor defect. The fix it describes was a new sump assembly plus repairing the wire loom inside the door, then insulating it from the door liner so it would not wear through again.

If your dishwasher is from those years, mention the door wiring when you book the visit. Taking the door apart and taping the harness is technician work, but knowing to look there can save a second trip.

What a technician will check

  • The sump, opened up, to see whether the chopper and the motor shaft turn freely. On the AppliancePartsPros forum, a technician says that if both spin freely and LE stays, the motor is shorted and the motor assembly needs replacing.
  • The impeller of the wash pump and the motor rotor for anything locking them, such as string around the shaft or a glass fragment in the pump vanes.
  • The wiring harness between the motor and the control board, plus the wire loom inside the door on older models, for chafed or broken wires.
  • The main control board, once the motor, harness and pump test fine.

What fixed it for other readers

No reader fixes yet. If you cleared LE, tell others what worked.

Reader fixes are shared by visitors and checked for safety, not tested by us.

Did you clear LE? Tell the next person what worked.

We publish your first name or initial, the month, and your fix. Nothing else.

Questions people ask about LG LE

How do I reset my LG dishwasher?

Press Power to turn it off, then switch off the dishwasher's circuit breaker for at least 10 seconds and turn it back on. Start a new cycle. This clears the display, but if the motor or its wiring is at fault, LE will show again and the dishwasher needs service.

Does LE mean the motor on my LG dishwasher is dead?

Not always. LG itself says the fault can be in the motor or in the harness between the motor and the control board, and repair threads describe debris jamming the shaft. A technician checks that the shaft spins freely and tests the wiring before replacing the motor.

My LG dishwasher shows LE and smells like burning. What should I do?

Turn it off and leave its breaker off. Do not run another cycle to test it. None of LG's LE pages or the repair threads cited here mention a burning smell, so do not assume the reset will settle it: have a technician check the motor and wiring first.

Sources