Frigidaire Dishwasher i30 Error Code: Water in Bottom Pan

Stop using itUpdated Checked against Frigidaire (Electrolux)

i30 on a Frigidaire dishwasher means a leak or overflow put water in the bottom pan under the tub. Turn it off at the breaker and dry the floor. Frigidaire's guide points to loose water inlet valve connections and an unlevel unit; extra suds and a poorly seated door gasket cause it too. If i30 returns, call a technician.

What to try first

Safety: Do not mop or reach into water around the dishwasher until its breaker is off. If the floor is wet, close the dishwasher's water shutoff as well, and leave the kick plate in place: the base pan behind it is for a technician.

  1. 1

    Cut the power, then deal with the water

    Switch the dishwasher off at the circuit breaker before you touch any water near it. If water has reached the floor, also close the shutoff valve that feeds the dishwasher, usually under the sink, and mop up.

  2. 2

    Check the supply line in the sink cabinet

    Look at the dishwasher's water line where it leaves the shutoff valve under the sink. Frigidaire's leaking checklist asks you to make sure the supply connections are secure and the line has no kinks. Wipe the fitting dry, wait a few minutes and look for new drops.

  3. 3

    Get the detergent right

    Use only fresh detergent made for automatic dishwashers, never hand or dish soap. Put in one tablet or the recommended amount, stay below the dispenser's fill lines, and do not pour detergent straight into the tub. Frigidaire's guide also says to measure carefully and to try a different brand if the leaking continues.

  4. 4

    Wipe up spilled rinse aid

    Frigidaire warns that spilled rinse aid foams and can lead to overflowing. Fill the rinse aid dispenser only to its fill mark and wipe any drips with a damp cloth before you start a cycle.

  5. 5

    Check the door gasket and the door closing

    Frigidaire's newer use and care guide asks you to check that the rubber door gasket is pressed into its mounting channel, reaches the bottom of the tub and does not run past the end rib, where it would stop the door closing. Make sure nothing in the racks keeps the door from shutting fully.

  6. 6

    See whether the dishwasher sits level

    Frigidaire's guide pairs i30 with making sure the unit is properly leveled. Pull out the lower rack and set a small level on the tub floor, first side to side, then front to back. If it is off, the legs need adjusting from under the front of the machine, which is a job for the installer or a technician.

  7. 7

    Reset and test

    Restore power and clear the code by pressing Cancel or by leaving the breaker off for five minutes, as Frigidaire's guide describes. If i30 is back at once, water is probably still sitting in the bottom pan.

Most likely causes of i30

  1. 1. Too many suds from the wrong detergent, too much of it, or spilled rinse aid (most common)

    Foam sits in the tub or along the door, you used hand dish soap or more than one tablet, or rinse aid dripped into the tub when you topped it up.

  2. 2. A loose connection at the water inlet valve (common)

    Water turns up under the dishwasher even when it has not run for hours, since the supply side of the valve stays under pressure all the time.

  3. 3. The dishwasher is not level (common)

    Water in the tub gathers in one corner, or the door sits unevenly against the tub opening, with a wider gap on one side.

  4. 4. A door gasket out of its channel, or a door that is not fully shut (common)

    Drips run from the lower corners of the door, the rubber seal has pulled out of its groove, or a tall pan or the kick plate keeps the door from closing all the way.

  5. 5. A leak inside the base: a pump seal, an internal hose or a valve that keeps filling (less common)

    Detergent, door and level all check out, yet the pan fills again after it has been dried.

  6. 6. A float stuck up, or a pressure switch fooled by food and grease (less common)

    The pan is dry, yet i30 stays on and the drain pump keeps running.

When to call a pro

  • i30 returns after the reset. Frigidaire's guide says to contact its customer care center when Cancel or five minutes at the breaker does not clear an error.
  • The connections at the water inlet valve need checking. Frigidaire's table names them for i30; leave that check to a technician.
  • The level check shows a tilt. The leveling legs are reached from under the front of the dishwasher.
  • Water keeps reaching the floor, or the bottom pan has to be dried out, which means sliding the dishwasher out of its opening.
  • The drain pump runs nonstop with the code showing and the cancel button does nothing.

What a i30 repair costs

$80–$200

HomeGuide's 2026 national figures, parts and labor included: $80 to $170 to replace a water inlet valve, $80 to $200 for a rubber door gasket and $90 to $190 for a float switch. A suds or rinse aid spill costs nothing. Tightening a fitting or leveling the unit needs no part, so mostly the visit: minimum service fees are $70 to $130 and cover the first hour.

Source

What Frigidaire means by the bottom pan

The error table in Frigidaire's use and care guide describes i30 as a leak or overflow of water detected in the bottom pan. That pan is the shallow tray under the tub, hidden behind the kick plate. iFixit's i30 guide shows a foam float sitting in it: when water collects there, the float lifts and the code appears.

The pan should always be dry, so the code tells you that water escaped, not where from. It could be a dripping fitting under the tub, suds pushing past the door seal, or a tub that filled too high.

Why the pump keeps running and the code comes straight back

Many owners first notice i30 because the drain pump will not stop, even with an empty tub. iFixit's guide says the pump may keep running to prevent an overflow. One AppliancePartsPros forum member described exactly this: a dry tub, a pump that kept going, a cancel button that no longer responded, and water coming in at the bottom corners of the door.

The code also tends to return the moment power is back, because the float stays up until the pan is dry. iFixit dries the pan with a shop vacuum or towels before testing again. Getting to the pan means sliding the dishwasher out, so that part is for a technician.

Frigidaire's two fixes, and one warning

Frigidaire's 2020 use and care guide gives just two fixes for i30: look for loose connections at the water inlet valve, and make sure the unit is properly leveled. You can check the level yourself from inside the tub. The inlet valve is a different matter: checking its fittings is a technician's job.

The same 2020 guide has a warning that matters here. Starting the dishwasher before the water is connected and turned on can damage the pump seal and lead to leaking. If the water was shut off for a plumbing job and a cycle ran anyway, tell the technician.

When i30 comes with i20

iFixit notes that i20 may appear alongside i30, often after a drain problem made the tub overfill. Frigidaire describes i20 as the dishwasher not draining properly. In that case, clear the drain first with Frigidaire's i20 checks: both filters, the sump and the drain hose. A dried pan will soon fill again if the tub keeps holding too much water.

What a technician will check

  • The bottom pan and its foam float: drying the pan so the float drops, then watching a test cycle to see where fresh water comes from.
  • The water inlet valve, its fittings and the fill hose, the first check on Frigidaire's i30 line.
  • The leveling legs, and how the door lines up with the tub.
  • The pump seal, the sump seals and the hoses and clamps inside the base.
  • The pressure switch and its channel from the sump. One Appliantology poster with a Frigidaire FPID2497R blamed food and grease in the pressure switch for an i30 with a drain pump that would not stop.
  • The float switch itself, tested once the pan is dry, when the code will not clear.

What fixed it for other readers

No reader fixes yet. If you cleared i30, tell others what worked.

Reader fixes are shared by visitors and checked for safety, not tested by us.

Did you clear i30? Tell the next person what worked.

We publish your first name or initial, the month, and your fix. Nothing else.

Questions people ask about Frigidaire i30

Can I keep using my Frigidaire dishwasher with an i30 code?

Not until you know where the water came from. Keep the breaker off, and keep the water valve closed if any reached the floor. A one-off suds spill is the exception: once the foam is gone and the pan has dried, a test cycle with proper detergent shows whether the code stays away.

Does i30 mean the float switch is bad?

Usually not. The float only reports water in the pan. A reply on the AppliancePartsPros forum puts it simply: pull the unit out and look in the very bottom pan. Water there means a leak somewhere; a dry pan with the code still on may point to a bad float switch.

How much does it cost to fix a Frigidaire i30 error?

Nothing when suds or a spill caused it. With a technician, HomeGuide's national ranges with labor are $80 to $170 for a water inlet valve, $80 to $200 for a door gasket and $90 to $190 for a float switch.

Sources