Frigidaire Dishwasher i20 Error Code: Won't Drain? Fixes

Fix soonUpdated Checked against Frigidaire US Support

Also shown or searched as: i40, iF0

i20 on a Frigidaire dishwasher means the unit did not drain properly. Switch it off, then clean both filters and the sump area, check that the drain hose is not pinched or blocked and rises at least 32 inches off the floor, and make sure a disposer's knockout plug is out. Then reset with Cancel or the breaker.

What to try first

Safety: Turn the dishwasher off at the breaker or unplug it before you reach into the tub, and give it time to cool: Frigidaire's guide warns of burns from the heating element. Switch the garbage disposer off before you look into its inlet.

  1. 1

    Turn the power off and let it cool

    Switch the dishwasher off at the circuit breaker or unplug it. Frigidaire's use and care guide warns that the heating element can burn you, so let the inside cool before you reach in.

  2. 2

    Clean both filters

    Pull out the lower rack. On models with a glass trap, lift it up and out by its handle, empty it and push it back down until it locks. On models with a cylinder fine filter, turn it counterclockwise, lift it out, empty it and rinse it under running water, using a sponge or bottle brush on stuck food. Then lift out the coarse filter beneath it and flush it under the tap.

  3. 3

    Clear the sump area

    With the filters out, sponge up the standing water and pick out any food, seeds or broken glass left in the sump below them. Frigidaire's i20 entry asks for the sump to be cleaned along with both filters.

  4. 4

    Free the drain hose under the sink

    Follow the hose as far as you can see it in the sink cabinet. Move anything stored against it and straighten any kink or flattened spot. Frigidaire's drain hose guide asks for the hose to rise at least 32 inches above the floor and then run down to the drain connection, never uphill into it.

  5. 5

    Empty the disposer and check its inlet

    If the hose connects to a garbage disposer, run the disposer so it is empty before the dishwasher drains. If the disposer is new, make sure the knockout plug inside its dishwasher inlet was removed; the disposer's instructions or its installer can confirm.

  6. 6

    Rinse out the air gap, if you have one

    An air gap is the small capped fitting on the countertop beside the faucet. Frigidaire says to take off the cover, empty what is inside and rinse it so the dishwasher can drain. It belongs to the plumbing, so Frigidaire's warranty does not cover it.

  7. 7

    Reset and run a short test

    Restore power and clear the code. Frigidaire's i20 article lists three ways: press and hold Cancel, switch off at the breaker, or unplug for three minutes (the owner's guide gives five minutes at the breaker). Run a rinse cycle and check that the tub is empty at the end.

Most likely causes of i20

  1. 1. Food soil packed into the filters or the sump (most common)

    Cloudy water stands over the filter at the bottom of the tub, or the glass trap or cylinder filter is full of seeds, labels, bones or bits of glass.

  2. 2. A drain hose that is pinched, kinked or blocked (common)

    The dishwasher was recently installed or pushed back into place, or boxes and cleaning bottles in the sink cabinet are pressing on the hose.

  3. 3. A garbage disposer that is full, or new with its knockout plug still in (common)

    i20 started the week a new disposer went in, or the disposer was packed with scraps when the dishwasher tried to pump out.

  4. 4. A drain hose that never climbs 32 inches above the floor (common)

    The hose lies along the bottom of the sink cabinet all the way to the drain, and the dishwasher has started to smell of old food.

  5. 5. Grease or food blocking the channel to the pressure switch (less common)

    Filters and hose are clear, yet i20 keeps coming back and the drain pump may run on and on.

  6. 6. A jammed or failed drain pump (less common)

    You hear a hum, buzz or scraping from under the tub while the water level does not drop, even after the filters and hose check out.

When to call a pro

  • i20 is back after you cleaned both filters and the sump, cleared the hose and reset. Frigidaire's owner's guide sends you to its customer care center at that point.
  • The drain pump hums, buzzes or scrapes, but the water in the tub stays put.
  • Getting to the hose, the pump or the pressure switch means sliding the dishwasher out of its opening or taking off the kick plate.
  • i30 shows up as well, meaning water has reached the bottom pan; drying that pan also means pulling the machine out.
  • Water pours out of the hose freely, yet the sink backs up whenever the dishwasher drains. That points to the house drain, which is a plumber's job.

What a i20 repair costs

$80–$400

HomeGuide's 2026 national prices with parts and labor: $80 to $180 for a new drain hose and $100 to $400 for a new drain pump, of which the pump itself is $20 to $100. Cleaning the filters and sump or freeing a pinched hose costs nothing; a service visit starts at a $70 to $130 minimum fee.

Source

i20, i40 and iF0 share one line in Frigidaire's guide

Frigidaire's support article titles i20 simply: unit did not drain properly. The error table in Frigidaire's use and care guide goes further and puts i20, i40 and iF0 on a single line, as clogged filters or a restricted drain line, with one set of fixes. That is why this page covers all three.

Frigidaire's support site also has a short article on i40 by itself, which it calls a clogged filter or sump and fixes by cleaning out the glass trap. So i40 points you at the filter first, while i20 sends you along the whole way out of the machine: filters, sump, hose, disposer and air gap.

Why Frigidaire wants the hose 32 inches up

Frigidaire's drain hose guide gives one number: keep the hose at least 32 inches above the floor, then let it run down to the drain connection. Frigidaire says this routing helps the dishwasher drain completely, which improves washing and keeps food soil from sitting in the sump and causing odors.

The two halves of that rule matter equally. A hose that lies flat along the cabinet floor misses the height, and one that climbs up to meet the drain at the end is the uphill routing Frigidaire's guide warns against. If a new sink, a plumbing repair or a cabinet clean-out moved the hose lately, check its route before anything else.

The small opening that trips the pressure switch

iFixit's i20 guide for Frigidaire Gallery dishwashers says i20 is often caused by contamination blocking the pressure switch channel. The pressure switch helps the dishwasher read its water level through a small hole in the sump near the filter opening. Packed with grease, that reading goes wrong, and the guide says the drain pump can keep running and set off the code.

The opening sits in the sump area, which Frigidaire's own i20 entry tells you to clean, so wipe gently around it while the filters are out. Cleaning the switch itself is different: iFixit slides the dishwasher out, unclips insulation and works on the underside, which is a job for a technician.

When i20 and i30 appear together

iFixit's i30 guide notes that i20 can show up alongside i30, often when a drain problem let the tub overfill. Frigidaire's table defines i30 as water detected in the bottom pan under the tub. Sort out the drain first; drying the pan will not hold for long if water still cannot leave the tub.

What a technician will check

  • The pressure switch under the tub and the channel that links it to the sump, which iFixit's i20 guide shows clogging with grease and food.
  • The drain pump and its impeller: whether it turns freely and what it sounds like. iFixit's not-draining guide ties a loud buzz to a blockage and a scrape to a damaged impeller.
  • The check valve on the drain side, one of the parts iFixit lists for a Frigidaire that will not drain.
  • The hidden length of the drain hose behind the dishwasher and its connection at the pump.
  • Power to the drain pump and the signal from the control board, when the pump does not run at all.

What fixed it for other readers

No reader fixes yet. If you cleared i20, tell others what worked.

Reader fixes are shared by visitors and checked for safety, not tested by us.

Did you clear i20? Tell the next person what worked.

We publish your first name or initial, the month, and your fix. Nothing else.

Questions people ask about Frigidaire i20

Can I keep using my Frigidaire dishwasher with an i20 code?

Not until it drains. Frigidaire's checks need no tools and take a few minutes, so do them before the next load. If water still stands in the tub after the reset and a rinse cycle, leave the dishwasher off and book service.

Is i20 a fill problem or a drain problem?

A drain problem. Both Frigidaire's support article and its use and care guide describe i20 as water not leaving the tub. A fill problem has its own code, i10, which Frigidaire's guide calls a low fill and links to a pinched supply line or a water shutoff that is not fully open.

Does i20 mean the drain pump is broken?

Usually not. Every fix on Frigidaire's i20 list is a filter, the sump, the hose, the disposer or the air gap. iFixit's not-draining guide also puts the pump near the end, after the filters, the hose, the air gap and the check valve.

How much does it cost to fix a Frigidaire i20 error?

Nothing if a filter, the sump or a pinched hose was the cause. If a part has to be replaced, HomeGuide's national figures with labor are $80 to $180 for a drain hose and $100 to $400 for a drain pump.

Sources