Bosch Dishwasher E09 Error Code: Heater Fault, What to Do
Also shown or searched as: E:09, F09, E2030
E09 on a Bosch dishwasher means a fault in the heater built into the heat pump, the pump that circulates the wash water. Bosch's first step is to switch off the breaker for 30 seconds and restore power. If E09 comes back, close the water supply, switch the dishwasher off and book a technician; Bosch advises against home repairs.
What to try first
Safety: Leave the heater and the pump to a technician: Bosch advises against home repairs of E09 for safety reasons. Switch the breaker off before anyone works on the machine, and do not open the base or the side panels yourself.
- 1
Turn the power off at the breaker
Bosch's US error-code list gives one home step for E09: switch off the dishwasher's circuit breaker, wait 30 seconds, then switch it back on. For codes their manuals do not list, Bosch's newer manuals ask for at least two minutes with the power off, so a longer wait is fine.
- 2
Run a normal program and watch the display
Switch the dishwasher on and start a regular cycle. If E09 stays away and the dishes come out hot and clean, nothing more needs doing for now.
- 3
If E09 returns, shut off the water and power
Press On/Off, close the water supply valve under the sink, and unplug the dishwasher or turn its breaker off again. Bosch's support pages for other markets give the same instruction and advise leaving the repair to an engineer.
- 4
Check the salt light, if your model has one
This applies only to dishwashers with a water softener. Bosch's UK page says that if the salt light is on together with E09, you should check the salt sensor is not dirty, because a dirty sensor can make the machine assume there is salt when none has been added. Your manual shows where the salt goes and how to refill it.
- 5
Write down the numbers Bosch will ask for
Note the code along with the E-Nr, FD and Z-Nr numbers. Bosch's manual says customer service needs all three, and they are printed on the rating label inside the door.
Most likely causes of E09
1. The heater inside the heat pump has failed (most common)
The wash water no longer gets hot, dishes come out dirty or very wet, and E09 shows during or at the end of the cycle.
2. A fault in the power module that switches the heater (common)
A technician's test shows the heater itself is fine, yet E09 keeps coming back.
3. A loose or damaged connection between the heater and the power module (less common)
E09 started right after other work inside the base, such as a control replacement, or it shows on some cycles and not on others.
4. A dirty salt sensor, on models with a water softener (less common)
The salt light is on at the same time as E09.
5. A one-off electronic fault (less common)
E09 clears once the power has been off at the breaker and stays away on the next few cycles.
When to call a pro
- E09 comes back after the breaker reset.
- The water stays cold or the dishes come out dirty, even while the code is not showing.
- Testing the heater means putting a meter on the pump inside the base with panels removed; Bosch advises against doing that at home.
What a E09 repair costs
$200–$600
HomeGuide's 2026 national ranges, parts and labor: a heating element $200 to $350, a motor $350 to $500 and a control board repair $200 to $600. On a Bosch the heater comes built into the circulation pump, so the line that applies depends on what the technician's test finds.
SourceWhat E09 means on a Bosch dishwasher
Bosch's US error-code list describes E09 as a heat pump internal heater fault, and its only home step is to cut the power at the breaker for 30 seconds. Bosch's UK page puts it more plainly: the heating element is defective. A Bosch support page for Ghana lists F09 alongside E09, and the US list gives the four-digit code E2030 the same description and the same breaker step.
Outside the US, Bosch's pages add a warning. They do not recommend trying to resolve E09 on your own, for safety reasons, and the Ghana page asks you to close the water tap and switch the appliance off.
Bosch's heat pump is the wash pump
The term heat pump can mislead. In Bosch's US list, the heat pump is a part with a motor (E01 is a heat pump motor circuit fault), it can jam (E21 says the heat pump is blocked) and it can scale up (E12). Put together, it is the pump that sprays the wash water around the tub, with the heater built in.
On the AppliancePartsPros forum, a parts technician answering an E09 question about a Bosch SHX68T56UC linked the circulation motor and heater assembly and noted that the element is installed in the circulation motor. On models built this way, a failed heater is replaced together with the pump.
E09 is not a limescale code
Bosch keeps scale separate. E12 on the US list, and E2060 on four-digit models, mean limescale has built up in the heat pump, and those come with a home fix: descale with a Bosch descaler and, on models with a softener, use softening salt. The newer manual gives the same fix for E:20-60, a calcified heating element. E09 gets no descaling step, only the power reset and a call to support.
The list also has a separate heater code for CrystalDry models: E2120 is a fault in the Zeolite chamber heater, which belongs to the drying system. E09 concerns the heater that warms the wash water.
Why the fix takes a technician
The heat pump sits under the tub, and its heater is wired to the power module in the base. A BSH technician sheet for an older Bosch model (SHX5AVF5UC) files E:09 as a defective heating circuit, and its heating checks end with one of two parts: the heat-pump assembly or the power module. Telling them apart takes an electrical test inside the machine.
Owners on automaticwasher.org describe what reaching the pump involves on a Bosch 800 Series: the videos they found showed a side panel and the main control coming off, or the whole bottom on models with the Zeolith drying system. On the AppliancePartsPros forum, one owner's E09 began right after the control board had been replaced, and that thread never found the cause.
What a technician will check
- The heater's resistance, measured at the circulation pump. On the AppliancePartsPros forum, a parts technician gave about 8.9 ohms as a good reading for one model (SHP865WF5N).
- If the heater reads wrong: the circulation pump and heater assembly, replaced as one unit (part 12008381 on the two models in those forum threads).
- If the heater reads right: the power module (part 12015863 for the SHP865WF5N, according to the same forum technician).
- The plugs and wiring between the heat pump and the power module, which the BSH technician sheet lists among its heating checks.
What fixed it for other readers
No reader fixes yet. If you cleared E09, tell others what worked.
Reader fixes are shared by visitors and checked for safety, not tested by us.
Questions people ask about Bosch E09
Will Bosch fix E09 under warranty?
If the dishwasher is still covered, go through Bosch. The manual says warranty repairs are carried out by an authorized service provider using genuine replacement parts, and the terms are in the Statement of Limited Product Warranty, which you can get from your retailer or Bosch's website.
Can I still get a heat pump for an older Bosch dishwasher?
For many years. The newer Bosch use and care manual says function-relevant genuine spare parts are available from Bosch customer service for up to 15 years from the date the model was placed on the market. Order by the E-Nr so the assembly matches your machine.
Is an E09 repair worth it, or should I replace the dishwasher?
Compare the quote with a new machine. HomeGuide's 2026 national figures put a new dishwasher at $600 to $1,700 installed, against $350 to $500 for a motor replacement and $200 to $600 for a control board repair. Ask which part failed before you decide, since the two are priced differently.
Sources
- Dishwasher Error Codes | Support | Bosch (Bosch US Owner Support, checked November 6, 2026)
- Dishwasher E09 error | Bosch UK (Bosch Home Appliances (UK), checked November 6, 2026)
- Error code 09 in display | Bosch (Bosch Home Appliances (Ghana), checked November 6, 2026)
- Dishwasher SHE53B75UC Use and Care Manual (BSH Home Appliances (Bosch), checked November 6, 2026)
- Bosch SHX5AVF5UC dishwasher error codes (technician sheet) (ApplianceAid (copy of a BSH service document), checked November 6, 2026)
- Bosch Dishwasher - Error E09 won't clean dishes and no heat (AppliancePartsPros forum, checked November 6, 2026)
- Bosch SHP865WF5N/11 Stopped Heating Water Midcycle Error Code E09 (AppliancePartsPros forum, checked November 6, 2026)
- Bosch E09 error after every cycle (AppliancePartsPros forum, checked November 6, 2026)
- BOSCH 800 Series throwing error code E:09 (automaticwasher.org forum, checked November 6, 2026)
- How Much Does Dishwasher Repair Cost? (2026) (HomeGuide, checked November 5, 2026)
