GE Dishwasher Error Code FTD: Not Draining? How to Fix It
Also shown or searched as: F56
GE dishwasher error code FTD, also shown as F56, means failure to drain: the dishwasher did not pump the water out. Clean the filters and the sump, check the drain hose under the sink for kinks, run the garbage disposer and clean the air gap, then cut power for a minute or two to reset it.
What to try first
Safety: Switch the dishwasher off before you reach into the tub, never put your hand into the garbage disposer, and never pour drain cleaner into the dishwasher. The drain pump, the pressure sensor and anything behind the kick plate are for a technician.
- 1
Look at how much water is left
Open the door once the cycle has stopped. On GE models without an Ultra Fine filter, 1 to 2 cups of clean water over the tub floor is normal. On models with one, water in the filter area is normal, but it should not cover the bottom of the tub.
- 2
Clear the sump and clean the filters
Switch the dishwasher off first. Take out the bottom rack and remove any food, paper or labels from the sump at the back of the tub. If your model has removable filters, twist the Ultra Fine filter counterclockwise to lift it out, then the Fine filter, and rinse both in warm soapy water with a sponge, not a scouring pad.
- 3
Check the drain hose under the sink
Follow the drain hose from where it connects below the sink and look for a kink, a pinch or something resting on it. Leave the panel below the dishwasher door in place; the rest of the hose is a job for a technician.
- 4
Run the disposer and clear the sink drain
If the sink drains slowly, clear it. If you have a garbage disposer, run it to empty the drain line, and run it before every dishwasher load. Never put your hand into the disposer to check it.
- 5
Clean the air gap
If there is a chrome cylinder behind the faucet, that is the air gap. Lift off the chrome cover, unscrew the plastic cap, remove any build-up and rinse the cap. Not every kitchen has one.
- 6
Check a newly installed disposer
If the disposer was recently installed or replaced, make sure the drain plug inside it was knocked out. The disposer's installation instructions show how.
- 7
Use the right detergent, and no drain cleaner
Use detergent made for automatic dishwashers, measured. Too much, or the wrong type, makes suds that can stop the water from draining. Never pour drain cleaner into the dishwasher.
- 8
Reset the power and run a cycle
Unplug the dishwasher or switch off its circuit breaker for a minute or two, then turn it back on and run a cycle. If the cause is cleared, FTD should not return.
Most likely causes of FTD
1. Clogged filters, or food or paper blocking the sump (most common)
Dirty water covers the bottom of the tub, and you find noodles, lettuce, bones or a label lying over the filter area at the back of the tub.
2. A kinked, blocked or worn drain hose (common)
The hose under the sink has a sharp bend, something presses on it, or an old hose was reused when the dishwasher went in.
3. A clogged sink drain, garbage disposer or air gap (common)
The kitchen sink drains slowly too, the disposer is full of food, or water spits from the small chrome cap behind the faucet when the dishwasher pumps out.
4. A new disposer with its knockout plug still in, or a drain hose with no high loop (less common)
FTD started right after a new disposer or a new dishwasher was put in, and the tub has never drained properly since.
5. Too many suds from the wrong detergent, or too much of it (less common)
There is foam in the tub when you open the door, or hand dish soap went into the dispenser.
6. A failed drain pump or a pressure sensor giving false readings (less common)
The filters, hose, air gap and disposer are all clear, yet FTD keeps coming back, whether water stays in the tub or the dishwasher seems to drain fine.
When to call a pro
- FTD comes back after the filter, hose, sink, disposer and air gap checks. GE says service will be needed at that point.
- It is a portable dishwasher hooked to the sink with the unicouple. GE says those need service when they will not drain.
- The dishwasher seems to drain fine, with no blockage you can find, yet FTD still shows.
- The drain hose needs replacing or a high loop needs setting, since that work happens behind and under the dishwasher.
- Water stays in the tub and you hear no pump running during the drain.
What a FTD repair costs
$80–$180
Cleaning the filters, air gap or disposer yourself costs nothing. GE names the drain hose as a cause, and HomeGuide's 2026 national list prices replacing a dishwasher drain hose at $80 to $180. If the visit only clears a clog, its minimum service fee of $70 to $130 covers the first hour. GE names no failed pump or sensor for FTD, and HomeGuide prices no pressure sensor repair.
SourceFTD, F56 and GE's other drain codes
GE's code list gives this fault two names: FTD or F56, both meaning failure to drain. The entry is short. The dishwasher did not drain, so check the drain hose, the air gap and the disposer, then work through GE's not-draining checklist.
The same list holds several older drain codes too. C1 means the pump-out ran longer than 2 minutes, and C3 means the dishwasher will not drain. GE notes that not all codes are found on all models, so which one you see depends on your dishwasher, while the checks are much the same.
Some water in the tub is normal
People often see a little water after a cycle and think the dishwasher is not draining. GE says 1 to 2 cups of clean water over the floor of the tub is normal on models without an Ultra Fine filter. A real drain fault usually leaves much more, often dirty, sometimes with a smell.
The opposite case comes up too: FTD with no water in the tub at all. Then the water did leave, so a clogged filter is less likely. The drain path can still be slow, though, so the hose, air gap and disposer checks still apply before you book a visit.
FTD when the dishwasher drains fine
If the tub empties and you find no blockage, the dishwasher may be misreading the water level. Appliance Repair Specialists lists a dirty or faulty pressure sensor as a cause that can trigger FTD through false readings. iFixit's guide to replacing the GE pressure sensor adds that build-up inside the sensor causes false readings and can stop the dishwasher partway through a wash.
GE gives a pressure sensor that sends an invalid signal its own code, PrS, so FTD does not point at the sensor first. The sensor sits under the front of the tub, behind the kick plate, so checking or replacing it is work for a technician, along with testing the drain pump.
After a new disposer or a new install
FTD right after kitchen work has its own suspects. A new disposer comes with a knockout plug in its dishwasher inlet; if nobody removed it, the dishwasher has nowhere to pump. GE also warns that reusing an old, worn drain hose can lead to kinks or a blockage, and that new GE dishwashers come with a white corrugated hose that should be used.
Without an air gap, the drain hose needs a high loop fastened under the counter at the height GE's installation instructions give. A hose that sags or runs too low can keep the dishwasher from draining. Setting that loop means working behind the machine, so leave it to the installer or a technician.
What a technician will check
- The drain pump and its impeller for debris or damage, with a continuity test on the pump, which The Kitchen Pro Tech says takes a multimeter.
- The chopper blade and the sump below the filters for a clog the filters did not catch.
- The pressure sensor under the front of the tub, for build-up inside it that iFixit's guide says can cause false readings.
- The full length of the drain hose and the height of its high loop, against GE's installation instructions.
What fixed it for other readers
No reader fixes yet. If you cleared FTD, tell others what worked.
Reader fixes are shared by visitors and checked for safety, not tested by us.
Questions people ask about GE FTD
How can I fix the FTD error on my GE dishwasher?
Start inside the tub and work outward: clean the filters and sump, then check the drain hose under the sink, the sink drain, the disposer and the air gap. Reset the power and run a cycle. If FTD returns, GE says the dishwasher needs service.
Is there a way to reset my GE dishwasher?
Yes. GE says disconnecting power for a minute or two can clear a fault code: unplug the dishwasher or switch off its breaker, then turn it back on. A reset only clears the display, so if the drain is still blocked, FTD will come back on the next cycle.
Why is my GE dishwasher beeping with an FTD code?
GE's code list mentions a beep only for C2, a pump-out that ran past 7 minutes, where pressing RESET stops it. For FTD it gives no beep step. Clear the drain and use the power reset; troubleshooting a beep that will not stop is a job for service.
Sources
- Dishwasher - Error, Fault or Function Codes (GE Appliances, checked November 11, 2026)
- Dishwasher - Not Draining (GE Appliances, checked November 11, 2026)
- Dishwasher - How to Clean Fine and Ultra Fine Filters (GE Appliances, checked November 11, 2026)
- Dishwasher - Cleaning the Air Gap (GE Appliances, checked November 11, 2026)
- GE Dishwasher FTD Error: What It Means & How to Fix It (Appliance Repair Specialists, checked November 11, 2026)
- GE Dishwasher FTD Code- Meaning, Causes, & How to Fix (The Kitchen Pro Tech, checked November 11, 2026)
- GE Dishwasher Pressure Sensor Replacement (iFixit, checked November 11, 2026)
- How Much Does Dishwasher Repair Cost? (2026) (HomeGuide, checked November 5, 2026)
